Magnetic sensors are designed to raise the speed pulses from the magnet attached to the rotating element.
Sensor assembly consists of a mechanical fixing in such a position to face the sensor was similar to the magnet which is fixed to the reflecting vehicle speed - it may be placed on the face of the magnet motorcycle , wheel hub, etc.
Sensors are manufactured in several versions, as described below.
Sensor with thread M8x1, 25 Fits KTM hub in place of the original speed sensor. At the end of the cable with a length of 1 m, is 3PIN female M8 connector. The sensor can be used as a substitute for sensors ICO tripmeter. For a convenient way to connect the sensor to the tripmeter Rally computer, it is necessary to harness the tripmeter Rally computer with M8 3PIN male or cable with M8 3PIN male. Sensor with thread M8x1, 25 Fits KTM hub in place of the original speed sensor. It has a long connection cable 1m. To connect the sensor to the tripmeter Rally computer use bundle that came with the odometer.
Sensor with thread M8x1, 25 with M8 3PIN, wire 1 mb
Code: CZU.M8.zlM8.1mb
Sensor with thread M8x1, 25, without connector, cable 2 mb
Code: CZU.M8. b/zl.1mb
Universal sensor fi 8 mm with M8 3PIN, wire 1 mb
Code: CZU.fi8.zlM8.1mb
Sensor housing with a diameter of 8 mm. At the end of the cable with a length of 1 m, is 3PIN female M8 connector. The sensor can be used as a substitute for sensors ICO tripmeter. For a convenient way to connect the sensor to the tripmeter Rally computer, it is necessary to harness the tripmeter Rally computer with M8 3PIN male or cable with M8 3PIN male. To install the mounting bracket can be used to probe the universal fi8mm or otherwise made their own bracket.
Sensor fi 8 mm universal connector and cable, 2 mbUniversal sensor fi 8 mm without connecotr, wire 1 mb
Code: CZU.fi8.b/zl.1mb
Sensor housing with a diameter of 8 mm. It has a long connection cable 1m. To connect the sensor to the tripmeter Rally computer use bundle that came with the odometer. To install the mounting bracket can be used to probe the universal fi8mm or otherwise made their own bracket.Magnet mount kit
Code: CZU.mag.duzy.b / or CZU.mag.duzy.z kl / kl
Set of 2 magnets neodymium to be fixed on the rotating element, the hub, the drive shaft, etc. The kit also includes a two-part putty after installation and check secure the magnet. By purchasing a set in our store, you can choose a set of universal Pattex contact adhesive that will help you mount the magnets. If you have a glue that will help you assemble, select the set without glue.Sensor mounting bracket universal fi 8 mm
Code: CZU.wspor.dofi8
Bracket kit with accessories for mounting the universal sensor. Fi8 sensor is attached to the bracket with 3 bands plastic in the designated holes on the bracket. Attach the bracket to the vehicle in any way, so that the sensor was close to the magnets. The kit consists of a console, 2 self-tapping screws, two screws M5 , cable ties to secure the sensor cable.Harness the tripmeter Rally computer with M8, 3PIN, 1m
Code: CZU.wiaz.6S. M8m.zas.
Harness to connect the odometer Rally computer containing the connector to the sensor with M8, 3PIN male and power cables.Sensor cable with M8 3PIN male
Code: CZU.prze.M8m.1mb
1 meter cable with M8, 3PIN male for connection of sensor with M8 connector, 3PIN, female.
Specifications
Power - 10 - 30 V
zone: up to 25 mm - depending on the magnet and mutual relationships magnet - the sensor
mount - M8 x 1.25 or universal fi8
output - NO